Skip to main content
Official Importer & Authorized Brands
Electrical & Lighting

Installing Flush-Mounted Sockets & Switches — Full Guide for Contractors 2026 | ramo.co.il

2026 guide to installing flush-mounted sockets and switches: Photex boxes, correct wiring, and IP44 waterproof points. Sapir series from ₪3, VAT included.

•7 min read
Flush-Mounted Sockets & Switches — ramo.co.il

Flush-mounted sockets and switches are the most common choice in new Israeli apartments and renovations, but incorrect installation can cause sparks, short circuits, or shock hazards. This guide covers installing the Sapir series and Photex recessed boxes, including correct wiring.

⚡

Quick Summary

✅ Electrical work in Israel must be done by a licensed electrician only
📦 The Photex recessed box must be installed before plastering, at the exact depth
🔌 Correct wiring: phase (brown), neutral (blue), ground (green-yellow)
⚠️ IP44 waterproof sockets are mandatory in bathrooms, kitchens and outdoors
💰 Sapir accessories start from just ₪3 per unit

What do you need before you start? 🧰

Prepare a drill, a voltage tester, wiring, and a 3-module Photex box or 4-module box depending on how many accessories you need at that point. For sockets, use the Sapir Recessed Power Socket or Sapir Power Socket for box 55, and for wet areas use a Waterproof Power Socket IP44. The switch line includes the Sapir Double Switch and Sapir Two-Way Switch.

⚠️

⚠️ Before you start

Under Israeli electrical regulations, only a licensed electrician may design, install, or test a final circuit. Always switch off the relevant breaker and RCD, and verify with a voltage tester that the box is dead before working.

Step by step — doing it right 👷

  1. Plan and cut power: Switch off the relevant breaker and RCD at the panel and confirm with a voltage tester.
  2. Cut the recess and install the Photex box: Match the box size (3 or 4 modules) to the number of accessories needed, and fix it firmly before plastering.
  3. Run the cables: Use 3x1.5mm² cable for sockets and 3x1mm² for switches, leaving about 15cm of slack on each side.
  4. Wire the accessory: Connect phase to brown, neutral to blue, and ground to green-yellow, tightening each terminal screw firmly.
  5. Insert the accessory into the box: Push gently until it clicks into place, checking alignment with a level.
  6. Attach the frame and cover plate (Sapir series): Match the finish to the wall.
  7. Final check: Restore the breaker and RCD, then test voltage and function with a tester.
💡

💡 Pro tip

Always leave about 15cm of slack cable inside the box — this lets you swap an accessory or fix a fault later without opening the wall again.

Products to buy on ramo.co.il 🛒

ImageProductPrice (incl. VAT)StockBuy
product
לחצן מדרגות מואר תחת הטיח ספיר לבן Nisko**₪14** incl. VAT✅ In Stock🛒 Buy
product
3 מודול - קופסת Photex (פוטקס) תת-טיח**₪3** incl. VAT✅ In Stock🛒 Buy
product
קופסה 4 מודול תה"ט - קופסת Photex (פוטקס)**₪3** incl. VAT✅ In Stock🛒 Buy
product
שקע כח תחת הטיח ספיר Nisko**₪7** incl. VAT✅ In Stock🛒 Buy
product
שקע חשמל כוח ספיר - לקופסה 55 Nisko**₪7** incl. VAT✅ In Stock🛒 Buy
product
מפסק כפול תחת הטיח ספיר לבן Nisko**₪9** incl. VAT✅ In Stock🛒 Buy
product
שקע כח מוגן מים IP44 Nisko**₪12** incl. VAT✅ In Stock🛒 Buy
product
מפסק מחליף תחת הטיח ספיר לבן Nisko**₪9** incl. VAT✅ In Stock🛒 Buy
❓

Frequently Asked Questions ❓

What's the difference between a 3-module and 4-module box?

The module count determines how many accessories (sockets/switches) can fit at that point. A 4-module box suits a double socket or a combined socket-and-switch point, while 3 modules is enough for a single accessory.

Where is an IP44 waterproof socket required?

Anywhere exposed to moisture or water — bathrooms, near kitchen sinks, balconies, and outdoor areas. This is required by Israeli standards for sealing rating and can't be compromised.

Can I install a socket myself?

Under Israeli electrical regulations, designing, installing, and testing a final circuit is reserved for a licensed electrician only. Incorrect wiring risks electric shock and fire.

What is a two-way switch and how is it different from a regular one?

A two-way switch lets you turn the same light on and off from two different locations (like both ends of a hallway), using different wiring than a standard switch.

🎯

Conclusion

Quality Sapir sockets and switches combine safety, clean design and affordable pricing. Plan your electrical points ahead and hire a licensed electrician for safe installation.